PAN4561

Make your product Powered by Panasonic

Overview

FCC Approved
The PAN4561 is an extended range 2.4GHz, ISM RF module. Modules may be configured from simple point-to-point proprietary devices to complex mesh networks by choosing from different firmware options.

Optional Synapse SNAP firmware provides a highly flexible, industry leading solution for mesh networking with a complete network development environment. The module uses the same FreeScale eight bit GT60 processor as Panasonic's popular PAN4555 making the two products application compatible. The PAN4561 has 55 pins allowing access to the full functionality of the MC13213 SOC. Low noise and power amplifiers have been added to the PAN4561 for extended range. With a maximum transmit power of 20dBm and receive sensitivity is -105dBm this module has a link margin of 125dBm, giving it the best range in its class.

Multiple antenna options are available including, ceramic antenna, SMD pad output, and UFL connector. This module complies with EN300328, FCC CFR Part 15 and ARIB STD-T66, FCC and IC certifications.

PAN4561 Full Specification
Applications
  • Remote Control And Wire Replacement In Industrial Systems Such As Wireless Sensor Networks
  • Factory Automation / Motor Control
  • Home Automation
  • Lighting Control
  • RFID Tagging
  • Inventory Management
  • Automated Meter Reading
  • Monitoring (Environmental, Patient or Fitness)
Product Performance
  • Small Size: 35mm X 15mm X 3.5mm
  • 3 Antenna Options: Single Port 50Ω, Ceramic Antenna or SMD Output
  • 16 Selectable Channels With 250 Kbps In The 2.4 Ghz Band
  • Low Power Modes For Increased Battery Life
  • High Sensitivity: -105 dBm Typical At 1% Packet Error Rate
  • 20 Dbm Typical Output Power Programmable Over 30 dB Range
  • Low Supply Voltage (2.7 V To 3.3 V, 3.0 V Typical)
  • Operating Temperature Range: -40°C To +85°C
  • Link Quality And Clear Channel Assessment Capability
  • 60k Flash And 4k RAM Memory
  • Two Uarts And One I2C Bus
  • 8 Channel A/d Converter With 10 Bit For Fast And Easy Conversion From Analog Inputs (Temperature, Pressure And Fluid Levels) To Digital Values
  • 5 Channel 16 Bit Timer/Pulse Width Modulation (Tpm) Outputs
  • BDM Port For Direct Download Programming
  • 39 Digital I/O Lines With Programmable Pull-Ups And Several With High-Current Driver



Specifications:

Parameter Value Condition / Notes
Receiver Sensitivity -105 dBm typical

For 1% packet error rate
Output Power 20 dBm Maximum
Power Supply 2.7 V to 3.3 V Single supply, 3.0 V typical
Power Control Range 30 dB  
Maximum Data Rate 250 kbps Over the air
Current Consumption
  Receive Mode
  Transmit Mode
  Idle Mode
  Doze Mode
  Hibernate Mode
  Off Mode

45 mA typ.
202 mA typ.
1.6 mA typ.
50 uA typ.
16 uA typ.
<2 uA typ.


Output power
nominal value

No CLKO
Operating Temperature Range -40°C to +85°C  


Notes:
All parameters are valid for VDD = 2.7V and Tamb = 25°C.

Freescale's MC13213 is included with the module, SMAC, MAC or Freescale Bee-Stack. There is no additional license fee per module by using the Freescale Bee-Stack, only a one time general support fee ($500) for the Bee-Stack to be paid to Freescale.

Mode Definitions and Transition Times for saving battery life can be seen in the data sheet MC1321x. The derivative MC13212 and MC13211 as well as a non-PA/LNA version are available on request.


Pin Layout:

Part Numbers:
ENW-C9A22A1EF 8 bit, LNA, PA, with Ceramic Antenna, No SW
ENW-C9A22C1EF 8 bit, LNA, PA, with RF Out on SMD Pads, No SW
ENW-C9A22B1EF 8 bit, LNA, PA, with U. FL Ant Connector, No SW
ENW-C9A22A2EF 8 bit, LNA, PA, Ceramic Ant, SN55 FW
ENW-C9A22B2EF 8 bit, LNA, PA, U.FL Connector, SN55 FW
ENW-C9A22C2EF 8 bit, LNA, PA, SMD RF Out, SN55 FW
ENW-C9A22A4EF 8 bit, LNA, PA, Ceramic Ant, SNAP FW
ENW-C9A22C4EF 8 bit, LNA, PA, SMD RF Out, SNAP FW
ENW-C9A22B4EF 8 bit, LNA, PA, U.FL Connector, SNAP FW
EVAL_PAN4561 Evaluation kit for the PAN4561