Foto de PROYECTOR DE 1 CHIP DLP PT-RZ470

PROYECTOR DE 1 CHIP DLP PT-RZ470

Power supply 100 – 240 V AC, 5.2 – 2.0 A, 50/60 Hz
Power consumption 460 W (470 VA) (250 W*¹ with LIGHT POWER set to NORMAL, 200 W*¹ with LIGHT POWER set to Ecosave1, 178 W*¹ with LIGHT POWER set to Ecosave2) (0.5 W with STANDBY MODE set to ECO*², 8 W with STANDBY MODE set to NORMAL)
DLP™ chip Panel size 16.5 mm (0.65 in) diagonal (16:9 aspect ratio)
Display method DLP™ chip × 1, DLP™ projection system
Pixels 2,073,600 (1,920 × 1,080) × 1, total of 2,073,600 pixels
Lens Manual zoom (2.0×), manual focus, F 2.0 – 3.4, f 21.5 –43.0 mm
Throw ratio 1.46 – 2.94:1
Light source LED/Laser-combined (R, B : LED; G : Laser diode)
Screen size (diagonal) 1.02 – 7.62 m (40 – 300 inches) diagonally, 16:9 aspect ratio
Brightness* ³ 3,500 lm
Center-to-corner uniformity* ³ 90 %
Contrast* ³ 20,000:1 ( full on/off )
Resolution 1,920 × 1,080 pixels ( Input signals that exceed this resolution will be conver ted to 1,920 × 1,080 pixels. )
Scanning frequency HDMI/DVI-I (digital) fH: 27– 100 kHz, fv: 24 –120 Hz, dot clock: 25–162 MHz
DVI-I (analog)/RGB fH: 15– 100 kHz, fv: 24 –120 Hz, dot clock: 162 MHz or lower
YPBPR (YCBCR) fH: 15.75 kHz, f V: 60 Hz [480i (525i)]
fH: 15.63 kHz, f V: 50 Hz [576i (625i)]
fH: 31.50 kHz, f V: 60 Hz [480p (525p)]
fH: 31.25 kHz, f V: 50 Hz [576p (625p)]
fH: 45.00 kHz, f V: 60 Hz [720 (750)/60p]
fH: 37.50 kHz, f V: 50 Hz [720 (750)/50p]
fH: 33.75 kHz, f V: 60 Hz [1035/60i]
fH: 33.75 kHz, f V: 60 Hz [1080 (1125)/60i]
fH: 28.13 kHz, f V: 50 Hz [1080 (1125)/50i]
fH: 28.13 kHz, f V: 25 Hz [1080 (1125)/25p]
fH: 27.00 kHz, f V: 24 Hz [1080 (1125)/24p]
fH: 27.00 kHz, f V: 48 Hz [1080 (1125)/24sF]
fH: 33.75 kHz, f V: 30 Hz [1080 (1125)/30p]
fH: 67.50 kHz, f V: 60 Hz [1080 (1125)/60p]
fH: 56.25 kHz, f V: 50 Hz [1080 (1125)/50p]
Video fH: 15.75 kHz, f V: 60 Hz [NTSC/NTSC4.43/PAL-M/PAL60] , fH: 15.63 kHz, f V: 50 Hz [PAL /PAL-N/SECAM]
Optical axis shift Ver tical: +73%, -48% (manual ), horizontal: +27%, -35% (manual )
Keystone correction range Vertical : ±40°
Installation Ceiling/floor, front /rear
Terminals HDMI IN HDMI 19-pin × 1 (Deep Color, compatible with HDCP) 480p (525p), 576p (625p), 720 (750) /60p, 720 (750) /50p, 1080 (1125) /60i, 1080 (1125) /50i, 1080 (1125) /25p, 1080 (1125) /24p, 1080 (1125) /24sF, 1080 (1125) /30p, 1080 (1125) /60p, 1080 (1125) /50p, VGA (640 × 480) –WUXGA* ⁴ (1,920 × 1,200), compatible with non-interlaced signals only, dot clock: 25–162 MHz, audio signal : linear PCM (sampling frequencies: 48 kHz, 44.1 kHz, 32 kHz)
DVI-I IN DVI-I 29-pin × 1 (DVI 1.0 compliant, compatible with HDCP, compatible with single link only)
Digital 480p (525p), 576p (625p), 720 (750) /60p, 720 (750) /50p, 1080 (1125) /60i,1080 (1125) /50i, 1080 (1125) /25p, 1080 (1125) /24p, 1080 (1125) /24sF, 1080 (1125) /30p, 1080 (1125) /60p, 1080 (1125) /50p,VGA (640 × 480) –WUXGA* ⁴ (1,920 × 1,200), compatible with non-interlaced signals only, dot clock: 25–162 MHz
RGB R/B: 0.7 Vp-p, 75 ohms, G : 0.7 Vp-p (G: 1.0 Vp-p for sync on G ), 75 ohms, HD/VD, SYNC: TTL, high impedance, positive/negative automatic
YPBPR/ YCBCR Y: 1.0 Vp-p ( including sync signal ), PB/PR (CB/CR) : 0.7 Vp-p, 75 ohms
COMPUTER (RGB) IN D-Sub HD 15-pin ( female) × 1 (RGB/ YPBPR/ YCBCR × 1)
VIDEO IN Pin jack × 1
AUDIO IN M3 ( L, R ) × 1
AUDIO OUT M3 ( L, R ) × 1
SERIAL IN D-sub 9-pin ( female) × 1 for external control (RS-232C compliant )
LAN / DIGITAL LINK RJ-45 × 1 ( for network and DIGITAL LINK (video/audio/network /serial control ) connection, 100Base-TX, compatible with PJLink™, HDCP compatible, Deep Color compatible) 1080 (1125) /50i, 1080 (1125) /25p, 1080 (1125) /24p, 1080 (1125) /24sF, 1080 (1125) /30p, 1080 (1125) /60p, 1080 (1125) /50p, VGA (640 × 480) –WUXGA* ⁴ (1,920 × 1,200), compatible with non-interlaced signals only, dot clock: 25–162 MHz
3D SYNC OUT Mini DIN 3-pin × 1, for 3D transmitter connection
Cabinet materials Molded plastic
Dimensions (W × H × D) 455 × 137*⁵ × 415 mm (17-29/32 × 5-13/32* ⁵ × 16-11/32 in) ( lens incuded)
Weight *⁶ Approximately 11.0 kg (24.3 lbs)
Operation noise* ³ 35 dB ( LIGHT POWER mode: NORMAL), 29 dB ( LIGHT POWER mode: LOW)
Operating environment Operating temperature: 0 – 45 °C*⁷ ( 32 –113 °F *⁷), operating humidity: 20– 80 % (no condensation)
Supplied accessories Power cord (with secure lock) × 1*⁸ , wireless remote control unit, batteries for remote control (R6/LR6/AA type × 2), sof tware CD-ROM ( Logo Transfer Software, Multi Projector Monitoring & Control Software)
Disclaimer *1 In STANDARD/GRAPHIC picture mode. Measured based on the power consumption rate and a measurement method for the TV receiver.
*2 When the standby mode is set to eco, network functions such as power on over the LAN network will not operate. Also, only certain commands can be received for external control using the serial terminal.
*3 Measurement, measuring conditions, and method of notation all comply with ISO 21118 international standards.
*4 WUXGA resolution is supported only when the signals are compliant with VESA CVT-RB (Coordinated Video Timing-Reduced Blanking).
*5 With legs at shortest position.
*6 Average value. May differ depending on the actual unit.
*7 0–40 °C (32 –104 °F) between 1,400 m and 2,700 m (4,593 ft and 8,858 ft) above sea level. If the ambient temperature exceeds 35 °C (95 °F), the light output may be reduced to protect the projector.
*8 Power cords available (× 2) for the PT-RZ470EA/RW430EA.
Weights and dimensions shown are approximate. Specifications and appearance are subject to change without notice. Product availability differs depending on region and country. This product may be subject to export control regulations. DLP, DLP logo and DLP Medallion logo are trademarks or registered trademarks of Texas Instruments. The projection distances and throw ratios given in this leaflet are for use only as guidelines. For more detailed information, please consult the dealer from whom you are purchasing the product. The PJLink trademark is an application trademark in Japan, the United States, and other countries and regions or registered trademarks. HDMI, the HDMI Logo, and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.All other trademarks are the property of their respective trademark owners. Projection images simulated.
© 2013 Panasonic Corporation. All rights reserved.
NOTES ON USE 1. Do not install the projector in locations that are subject to excessive water, humidity, steam, or oily smoke. Doing so may result in fire, malfunction, or electric shock.
2. Please observe the following precautions:
• Never place objects on top of the projector while it is operation.
• Make sure there is an unobstructed space of 500 mm (1 ft 8 in) or more around the projector’s exhaust openings.
• Do not stack projector units directly on top of one another for the purpose of multiple (stacked) projection. When stacking projector units, be sure to provide the amount of space indicated below between them. These space requirements also apply to installations where only one projector unit is operating at one time and the other unit is used as a backup.
• Make sure that nothing blocks the projector’s air intake and exhaust openings. Also, install theprojector so that cool or hot air from other air conditioning equipment does not flow directly toward the projector’s air intake or exhaust openings.
• Do not install the projector in an enclosed space. If it is necessary to install it in an enclosed space, add a separate ventilation system. If ventilation is insufficient, hot air will accumulate at the intake opening. This may cause the projector’s protective circuit to interrupt projector operation.
• If the projector is placed in a box, ensure that the projector’s intake and exhaust openings are not blocked. Take particular care to ensure that hot air from the exhaust openings is not sucked into the intake openings.
• To install and use the projector via a method that does not use the adjustable feet in a floor standing installation, fix the projector using the four screw holes for ceiling mounting. (Screw diameter: M4, tapping depth inside the set: 10 mm, torque: 1.25 ± 0.2 N·m)